Extruder/Hotend

Grid List

Set Descending Direction

1-10 of 297

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  1. RepRap M6 Brass Nozzle 3mm -  0,4 mm - 4 pcs
    Excl. Tax: $20.81 Incl. Tax: $26.01

    RepRap M6 Brass Nozzle 0,4 mm. Contains 4 nozzles.

    Compatible withUM2+, Olsson Block, Wanhao i3 Mini

    The premium nozzles from PrimaCreator are a series of replacement nozzles that can make more difference for the result than you may think. To have a high-quality nozzle is like having a sharp pencil, you need it to get a great print.

    All nozzles from PrimaCreator are made from the best high-quality brass or steel (depending on type) and are completed in a state of the art factory. All nozzles are manufactured with a tolerance of less than ± 0.01 mm. This means that your filament will have a very smooth and clear surface while extruding which, of course, results in better prints.

    For best results and optimal print quality, we highly recommend that you re-level your build plate after changing to a new nozzle. Note that a PrimaCreator nozzle might be compatible with your printer, but the distance between nozzle and build plate must be adjusted.

    The process of making a PrimaCreator nozzle begins with a selected high-quality material. When the material reaches the factory, there is first an optical inspection made of the material that are going to be used for each batch of nozzles. Then it´s time to clamp the material, in other words, make it into a long rod. In our process this only is done once, in many other (cheaper) cases, this process must be repeated several times, often as many as 3-4 times and yet you don´t get the same results.

    After this process, the material goes through an ultrasonic cleaning bath and after that it is cleaned again and protected against surface oxidation.

    The nozzle will now take shape with millimeter precision, the tolerance is less than ± 0.01 mm.

    The process of removing sharp edges from the nozzles is a very important step as this makes up a big part of the result. If there is to much sharp edges left on the nozzle it will make the nozzle more prone to clog. So it´s essential that the nozzle is very smooth and clean before it is used. In every batch a few nozzles are selected and cut in half to make sure that every specification is met, and that the surface is in perfect condition.

    The nozzles are then checked for one last time and packed individually in a protective box – ready to be shipped to you.

    The series of nozzles from PrimaCreator is the perfect choice for people who only wants the best and at a great value!

    Marks/dots on Nozzle = Size

    • 0 = 0.20mm
    • 3 = 0.40mm
    • 4 = 0.60mm
    • 5 = 0.80mm
    Learn More
  2. BondTech Drivegear Kit 1.75 mm / 8 mm
    Excl. Tax: $55.08 Incl. Tax: $68.85

    These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft.

    • Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4 x 22 mm shaft.

    A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

    Learn More
  3. BondTech Drivegear Kit 2.85-3.0 mm / 8 mm
    Excl. Tax: $55.08 Incl. Tax: $68.85

    These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft.

    • Gear set for filament size 2.85 - 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4 x 22 mm shaft.

    A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

    Learn More
  4. BondTech Bowden Adapter 2.85-3.0 mm / 6 mm
    Excl. Tax: $9.33 Incl. Tax: $11.66

    Dimensions 1.5 × 1.6 × 1.6 cm
    Size

    6mm

    Learn More
  5. BondTech Nema17 Pancake Stepper 22 mm
    Excl. Tax: $14.38 Incl. Tax: $17.98

    Max Input current: 0.8A
    Step angle: 1.8 deg.
    Torque: 12 Ncm
    Outputshaft diameter: 5.0 mm with flat.
    Hole for mounting: 31 mm, 4xM3
    Motor lenght: 22mm

    Learn More
  6. BondTech  Nema17 Pancake Stepper 25 mm
    Excl. Tax: $16.37 Incl. Tax: $20.46

    Max Input current: 0.7A per phase
    Step angle: 1.8 deg.
    Torque: 18 Ncm
    Outputshaft diameter: 5.0 mm
    Hole for mounting: 31 mm, 4xM3
    Motor lenght: 25mm

    Learn More
  7. BondTech Nema17 Geared Stepper
    Excl. Tax: $37.64 Incl. Tax: $47.05

    Weight: 406g
    Max Input current: 1.2A
    Step angle: 1.8 deg.
    Gear ratio: 5.18:1
    Outputshaft diameter: 8.0 mm
    Hole circle for mounting: 28 mm, 4xM3
    Motor lenght: 40mm

    Learn More
  8. BondTech Adapter Cable Raise3D Dual
    Excl. Tax: $3.37 Incl. Tax: $4.21

    Dimensions 10 cm
    Learn More
  9. BondTech Motor Cable JST-XH6 - PC2510
    Excl. Tax: $2.30 Incl. Tax: $2.88

    This cable is by default wired for our 40 mm Geared Nema17 motor, please make sure that it follows the schematics for your application.

    Controller side           Motor side
    PIN 1  —————– PIN 1
    PIN 2 —————– PIN 4
    PIN 3 —————– PIN 3
    PIN 4 —————– PIN 6

    Dimensions 70 cm
    Learn More
  10. BondTech Motor Cable JST-XH6 -  JST-XH4
    Excl. Tax: $1.68 Incl. Tax: $2.10

    This cable is by default wired for our 40 mm Geared Nema17 motor, please make sure that it follows the schematics for your application.

    Controller side      Motor side
    PIN 1  —————– PIN 1
    PIN 2 —————– PIN 4
    PIN 3 —————– PIN 3
    PIN 4 —————– PIN 6

    Dimensions 70 cm
    Learn More

Grid List

Set Descending Direction

1-10 of 297

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
This site uses cookies. By continuing to browse this site you are agreeing to our use of cookies. Find out more here.
x